a numeric context, you get a normal increment. If, however, the
variable has been used in only string contexts since it was set, and
has a value that is not the empty string and matches the pattern
-C</^[a-zA-Z]*[0-9]*$/>, the increment is done as a string, preserving each
+C</^[a-zA-Z]*[0-9]*\z/>, the increment is done as a string, preserving each
character within its range, with carry:
print ++($foo = '99'); # prints '100'
C<$a>. If C<$b> is negative, then C<$a % $b> is C<$a> minus the
smallest multiple of C<$b> that is not less than C<$a> (i.e. the
result will be less than or equal to zero).
-Note than when C<use integer> is in scope, "%" give you direct access
+Note than when C<use integer> is in scope, "%" gives you direct access
to the modulus operator as implemented by your C compiler. This
operator is not as well defined for negative operands, but it will
execute faster.
Binary "<=>" returns -1, 0, or 1 depending on whether the left
argument is numerically less than, equal to, or greater than the right
-argument.
+argument. If your platform supports NaNs (not-a-numbers) as numeric
+values, using them with "<=>" (or any other numeric comparison)
+returns undef.
Binary "eq" returns true if the left argument is stringwise equal to
the right argument.
Binary "ne" returns true if the left argument is stringwise not equal
to the right argument.
-Binary "cmp" returns -1, 0, or 1 depending on whether the left argument is stringwise
-less than, equal to, or greater than the right argument.
+Binary "cmp" returns -1, 0, or 1 depending on whether the left
+argument is stringwise less than, equal to, or greater than the right
+argument.
"lt", "le", "ge", "gt" and "cmp" use the collation (sort) order specified
by the current locale if C<use locale> is in effect. See L<perllocale>.
printing C<"\n"> may emit no actual data. In general, use C<"\n"> when
you mean a "newline" for your system, but use the literal ASCII when you
need an exact character. For example, most networking protocols expect
-and prefer a CR+LF (C<"\012\015"> or C<"\cJ\cM">) for line terminators,
+and prefer a CR+LF (C<"\015\012"> or C<"\cM\cJ">) for line terminators,
and although they often accept just C<"\012">, they seldom tolerate just
C<"\015">. If you get in the habit of using C<"\n"> for networking,
you may be burned some day.
You can intermix C<m//g> matches with C<m/\G.../g>, where C<\G> is a
zero-width assertion that matches the exact position where the previous
-C<m//g>, if any, left off. The C<\G> assertion is not supported without
-the C</g> modifier. (Currently, without C</g>, C<\G> behaves just like
-C<\A>, but that's accidental and may change in the future.)
+C<m//g>, if any, left off. Without the C</g> modifier, the C<\G> assertion
+still anchors at pos(), but the match is of course only attempted once.
+Using C<\G> without C</g> on a target string that has not previously had a
+C</g> match applied to it is the same as using the C<\A> assertion to match
+the beginning of the string.
Examples:
($one,$five,$fifteen) = (`uptime` =~ /(\d+\.\d+)/g);
# scalar context
- $/ = ""; $* = 1; # $* deprecated in modern perls
+ $/ = "";
while (defined($paragraph = <>)) {
while ($paragraph =~ /[a-z]['")]*[.!?]+['")]*\s/g) {
$sentences++;
print "3: '";
print $1 while /(p)/gc; print "', pos=", pos, "\n";
}
+ print "Final: '$1', pos=",pos,"\n" if /\G(.)/;
The last example should print:
1: '', pos=7
2: 'q', pos=8
3: '', pos=8
+ Final: 'q', pos=8
+
+Notice that the final match matched C<q> instead of C<p>, which a match
+without the C<\G> anchor would have done. Also note that the final match
+did not update C<pos> -- C<pos> is only updated on a C</g> match. If the
+final match did indeed match C<p>, it's a good bet that you're running an
+older (pre-5.6.0) Perl.
A useful idiom for C<lex>-like scanners is C</\G.../gc>. You can
combine several regexps like this to process a string part-by-part,
=item `STRING`
-A string which is (possibly) interpolated and then executed as a system
-command with C</bin/sh> or its equivalent. Shell wildcards, pipes,
-and redirections will be honored. The collected standard output of the
-command is returned; standard error is unaffected. In scalar context,
-it comes back as a single (potentially multi-line) string. In list
-context, returns a list of lines (however you've defined lines with $/
-or $INPUT_RECORD_SEPARATOR).
+A string which is (possibly) interpolated and then executed as a
+system command with C</bin/sh> or its equivalent. Shell wildcards,
+pipes, and redirections will be honored. The collected standard
+output of the command is returned; standard error is unaffected. In
+scalar context, it comes back as a single (potentially multi-line)
+string, or undef if the command failed. In list context, returns a
+list of lines (however you've defined lines with $/ or
+$INPUT_RECORD_SEPARATOR), or an empty list if the command failed.
Because backticks do not affect standard error, use shell file descriptor
syntax (assuming the shell supports this) if you care to address this.
projects / p5sagit/p5-mst-13.2.git / blobdiff