Integrate perlio:

[p5sagit/p5-mst-13.2.git] / pod / perlfaq5.pod

=head1 NAME

perlfaq5 - Files and Formats ($Revision: 1.12 $, $Date: 2002/03/11 22:25:25 $)

=head1 DESCRIPTION

This section deals with I/O and the "f" issues: filehandles, flushing,
formats, and footers.

=head2 How do I flush/unbuffer an output filehandle?  Why must I do this?

The C standard I/O library (stdio) normally buffers characters sent to
devices.  This is done for efficiency reasons so that there isn't a
system call for each byte.  Any time you use print() or write() in
Perl, you go though this buffering.  syswrite() circumvents stdio and
buffering.

In most stdio implementations, the type of output buffering and the size of
the buffer varies according to the type of device.  Disk files are block
buffered, often with a buffer size of more than 2k.  Pipes and sockets
are often buffered with a buffer size between 1/2 and 2k.  Serial devices
(e.g. modems, terminals) are normally line-buffered, and stdio sends
the entire line when it gets the newline.

Perl does not support truly unbuffered output (except insofar as you can
C<syswrite(OUT, $char, 1)>).  What it does instead support is "command
buffering", in which a physical write is performed after every output
command.  This isn't as hard on your system as unbuffering, but does
get the output where you want it when you want it.

If you expect characters to get to your device when you print them there,
you'll want to autoflush its handle.
Use select() and the C<$|> variable to control autoflushing
(see L<perlvar/$|> and L<perlfunc/select>):

    $old_fh = select(OUTPUT_HANDLE);
    $| = 1;
    select($old_fh);

Or using the traditional idiom:

    select((select(OUTPUT_HANDLE), $| = 1)[0]);

Or if don't mind slowly loading several thousand lines of module code
just because you're afraid of the C<$|> variable:

    use FileHandle;
    open(DEV, "+</dev/tty");      # ceci n'est pas une pipe
    DEV->autoflush(1);

or the newer IO::* modules:

    use IO::Handle;
    open(DEV, ">/dev/printer");   # but is this?
    DEV->autoflush(1);

or even this:

    use IO::Socket;               # this one is kinda a pipe?
    $sock = IO::Socket::INET->new(PeerAddr => 'www.perl.com',
                                  PeerPort => 'http(80)',
                                  Proto    => 'tcp');
    die "$!" unless $sock;

    $sock->autoflush();
    print $sock "GET / HTTP/1.0" . "\015\012" x 2;
    $document = join('', <$sock>);
    print "DOC IS: $document\n";

Note the bizarrely hard coded carriage return and newline in their octal
equivalents.  This is the ONLY way (currently) to assure a proper flush
on all platforms, including Macintosh.  That's the way things work in
network programming: you really should specify the exact bit pattern
on the network line terminator.  In practice, C<"\n\n"> often works,
but this is not portable.

See L<perlfaq9> for other examples of fetching URLs over the web.

=head2 How do I change one line in a file/delete a line in a file/insert a line in the middle of a file/append to the beginning of a file?

Use the Tie::File module, which is included in the standard
distribution since Perl 5.8.0.

=head2 How do I count the number of lines in a file?

One fairly efficient way is to count newlines in the file. The
following program uses a feature of tr///, as documented in L<perlop>.
If your text file doesn't end with a newline, then it's not really a
proper text file, so this may report one fewer line than you expect.

    $lines = 0;
    open(FILE, $filename) or die "Can't open `$filename': $!";
    while (sysread FILE, $buffer, 4096) {
        $lines += ($buffer =~ tr/\n//);
    }
    close FILE;

This assumes no funny games with newline translations.

=head2 How do I make a temporary file name?

Use the File::Temp module, see L<File::Temp> for more information.

  use File::Temp qw/ tempfile tempdir /; 

  $dir = tempdir( CLEANUP => 1 );
  ($fh, $filename) = tempfile( DIR => $dir );

  # or if you don't need to know the filename

  $fh = tempfile( DIR => $dir );

The File::Temp has been a standard module since Perl 5.6.1.  If you
don't have a modern enough Perl installed, use the C<new_tmpfile>
class method from the IO::File module to get a filehandle opened for
reading and writing.  Use it if you don't need to know the file's name:

    use IO::File;
    $fh = IO::File->new_tmpfile()
        or die "Unable to make new temporary file: $!";

If you're committed to creating a temporary file by hand, use the
process ID and/or the current time-value.  If you need to have many
temporary files in one process, use a counter:

    BEGIN {
        use Fcntl;
        my $temp_dir = -d '/tmp' ? '/tmp' : $ENV{TMPDIR} || $ENV{TEMP};
        my $base_name = sprintf("%s/%d-%d-0000", $temp_dir, $$, time());
        sub temp_file {
            local *FH;
            my $count = 0;
            until (defined(fileno(FH)) || $count++ > 100) {
                $base_name =~ s/-(\d+)$/"-" . (1 + $1)/e;
                sysopen(FH, $base_name, O_WRONLY|O_EXCL|O_CREAT);
            }
            if (defined(fileno(FH))
                return (*FH, $base_name);
            } else {
                return ();
            }
        }
    }

=head2 How can I manipulate fixed-record-length files?

The most efficient way is using pack() and unpack().  This is faster than
using substr() when taking many, many strings.  It is slower for just a few.

Here is a sample chunk of code to break up and put back together again
some fixed-format input lines, in this case from the output of a normal,
Berkeley-style ps:

    # sample input line:
    #   15158 p5  T      0:00 perl /home/tchrist/scripts/now-what
    $PS_T = 'A6 A4 A7 A5 A*';
    open(PS, "ps|");
    print scalar <PS>; 
    while (<PS>) {
        ($pid, $tt, $stat, $time, $command) = unpack($PS_T, $_);
        for $var (qw!pid tt stat time command!) {
            print "$var: <$$var>\n";
        }
        print 'line=', pack($PS_T, $pid, $tt, $stat, $time, $command),
                "\n";
    }

We've used C<$$var> in a way that forbidden by C<use strict 'refs'>.
That is, we've promoted a string to a scalar variable reference using
symbolic references.  This is okay in small programs, but doesn't scale
well.   It also only works on global variables, not lexicals.

=head2 How can I make a filehandle local to a subroutine?  How do I pass filehandles between subroutines?  How do I make an array of filehandles?

The fastest, simplest, and most direct way is to localize the typeglob
of the filehandle in question:

    local *TmpHandle;

Typeglobs are fast (especially compared with the alternatives) and
reasonably easy to use, but they also have one subtle drawback.  If you
had, for example, a function named TmpHandle(), or a variable named
%TmpHandle, you just hid it from yourself.

    sub findme {
        local *HostFile;
        open(HostFile, "</etc/hosts") or die "no /etc/hosts: $!";
        local $_;               # <- VERY IMPORTANT
        while (<HostFile>) {
            print if /\b127\.(0\.0\.)?1\b/;
        }
        # *HostFile automatically closes/disappears here
    }

Here's how to use typeglobs in a loop to open and store a bunch of
filehandles.  We'll use as values of the hash an ordered
pair to make it easy to sort the hash in insertion order.

    @names = qw(motd termcap passwd hosts);
    my $i = 0;
    foreach $filename (@names) {
        local *FH;
        open(FH, "/etc/$filename") || die "$filename: $!";
        $file{$filename} = [ $i++, *FH ];
    }

    # Using the filehandles in the array
    foreach $name (sort { $file{$a}[0] <=> $file{$b}[0] } keys %file) {
        my $fh = $file{$name}[1];
        my $line = <$fh>;
        print "$name $. $line";
    }

For passing filehandles to functions, the easiest way is to 
preface them with a star, as in func(*STDIN).  
See L<perlfaq7/"Passing Filehandles"> for details.

If you want to create many anonymous handles, you should check out the
Symbol, FileHandle, or IO::Handle (etc.) modules.  Here's the equivalent
code with Symbol::gensym, which is reasonably light-weight:

    foreach $filename (@names) {
        use Symbol;
        my $fh = gensym();
        open($fh, "/etc/$filename") || die "open /etc/$filename: $!";
        $file{$filename} = [ $i++, $fh ];
    }

Here's using the semi-object-oriented FileHandle module, which certainly
isn't light-weight:

    use FileHandle;

    foreach $filename (@names) {
        my $fh = FileHandle->new("/etc/$filename") or die "$filename: $!";
        $file{$filename} = [ $i++, $fh ];
    }

Please understand that whether the filehandle happens to be a (probably
localized) typeglob or an anonymous handle from one of the modules
in no way affects the bizarre rules for managing indirect handles.
See the next question.

=head2 How can I use a filehandle indirectly?

An indirect filehandle is using something other than a symbol
in a place that a filehandle is expected.  Here are ways
to get indirect filehandles:

    $fh =   SOME_FH;       # bareword is strict-subs hostile
    $fh =  "SOME_FH";      # strict-refs hostile; same package only
    $fh =  *SOME_FH;       # typeglob
    $fh = \*SOME_FH;       # ref to typeglob (bless-able)
    $fh =  *SOME_FH{IO};   # blessed IO::Handle from *SOME_FH typeglob

Or, you can use the C<new> method from the FileHandle or IO modules to
create an anonymous filehandle, store that in a scalar variable,
and use it as though it were a normal filehandle.

    use FileHandle;
    $fh = FileHandle->new();

    use IO::Handle;                     # 5.004 or higher
    $fh = IO::Handle->new();

Then use any of those as you would a normal filehandle.  Anywhere that
Perl is expecting a filehandle, an indirect filehandle may be used
instead. An indirect filehandle is just a scalar variable that contains
a filehandle.  Functions like C<print>, C<open>, C<seek>, or
the C<< <FH> >> diamond operator will accept either a read filehandle
or a scalar variable containing one:

    ($ifh, $ofh, $efh) = (*STDIN, *STDOUT, *STDERR);
    print $ofh "Type it: ";
    $got = <$ifh>
    print $efh "What was that: $got";

If you're passing a filehandle to a function, you can write
the function in two ways:

    sub accept_fh {
        my $fh = shift;
        print $fh "Sending to indirect filehandle\n";
    }

Or it can localize a typeglob and use the filehandle directly:

    sub accept_fh {
        local *FH = shift;
        print  FH "Sending to localized filehandle\n";
    }

Both styles work with either objects or typeglobs of real filehandles.
(They might also work with strings under some circumstances, but this
is risky.)

    accept_fh(*STDOUT);
    accept_fh($handle);

In the examples above, we assigned the filehandle to a scalar variable
before using it.  That is because only simple scalar variables, not
expressions or subscripts of hashes or arrays, can be used with
built-ins like C<print>, C<printf>, or the diamond operator.  Using
something other than a simple scalar variable as a filehandle is
illegal and won't even compile:

    @fd = (*STDIN, *STDOUT, *STDERR);
    print $fd[1] "Type it: ";                           # WRONG
    $got = <$fd[0]>                                     # WRONG
    print $fd[2] "What was that: $got";                 # WRONG

With C<print> and C<printf>, you get around this by using a block and
an expression where you would place the filehandle:

    print  { $fd[1] } "funny stuff\n";
    printf { $fd[1] } "Pity the poor %x.\n", 3_735_928_559;
    # Pity the poor deadbeef.

That block is a proper block like any other, so you can put more
complicated code there.  This sends the message out to one of two places:

    $ok = -x "/bin/cat";                
    print { $ok ? $fd[1] : $fd[2] } "cat stat $ok\n";
    print { $fd[ 1+ ($ok || 0) ]  } "cat stat $ok\n";           

This approach of treating C<print> and C<printf> like object methods
calls doesn't work for the diamond operator.  That's because it's a
real operator, not just a function with a comma-less argument.  Assuming
you've been storing typeglobs in your structure as we did above, you
can use the built-in function named C<readline> to reads a record just
as C<< <> >> does.  Given the initialization shown above for @fd, this
would work, but only because readline() require a typeglob.  It doesn't
work with objects or strings, which might be a bug we haven't fixed yet.

    $got = readline($fd[0]);

Let it be noted that the flakiness of indirect filehandles is not
related to whether they're strings, typeglobs, objects, or anything else.
It's the syntax of the fundamental operators.  Playing the object
game doesn't help you at all here.

=head2 How can I set up a footer format to be used with write()?

There's no builtin way to do this, but L<perlform> has a couple of
techniques to make it possible for the intrepid hacker.

=head2 How can I write() into a string?

See L<perlform/"Accessing Formatting Internals"> for an swrite() function.

=head2 How can I output my numbers with commas added?

This one from Benjamin Goldberg will do it for you:

   s/(^[-+]?\d+?(?=(?>(?:\d{3})+)(?!\d))|\G\d{3}(?=\d))/$1,/g;

or written verbosely:

   s/(
       ^[-+]?            # beginning of number.
       \d{1,3}?          # first digits before first comma
       (?=               # followed by, (but not included in the match) :
          (?>(?:\d{3})+) # some positive multiple of three digits.
          (?!\d)         # an *exact* multiple, not x * 3 + 1 or whatever.
       )
      |                  # or:
       \G\d{3}           # after the last group, get three digits
       (?=\d)            # but they have to have more digits after them.
   )/$1,/xg;

=head2 How can I translate tildes (~) in a filename?

Use the <> (glob()) operator, documented in L<perlfunc>.  Older
versions of Perl require that you have a shell installed that groks
tildes.  Recent perl versions have this feature built in. The
File::KGlob module (available from CPAN) gives more portable glob
functionality.

Within Perl, you may use this directly:

        $filename =~ s{
          ^ ~             # find a leading tilde
          (               # save this in $1
              [^/]        # a non-slash character
                    *     # repeated 0 or more times (0 means me)
          )
        }{
          $1
              ? (getpwnam($1))[7]
              : ( $ENV{HOME} || $ENV{LOGDIR} )
        }ex;

=head2 How come when I open a file read-write it wipes it out?

Because you're using something like this, which truncates the file and
I<then> gives you read-write access:

    open(FH, "+> /path/name");          # WRONG (almost always)

Whoops.  You should instead use this, which will fail if the file
doesn't exist.  

    open(FH, "+< /path/name");          # open for update

Using ">" always clobbers or creates.  Using "<" never does
either.  The "+" doesn't change this.

Here are examples of many kinds of file opens.  Those using sysopen()
all assume

    use Fcntl;

To open file for reading:

    open(FH, "< $path")                                 || die $!;
    sysopen(FH, $path, O_RDONLY)                        || die $!;

To open file for writing, create new file if needed or else truncate old file:

    open(FH, "> $path") || die $!;
    sysopen(FH, $path, O_WRONLY|O_TRUNC|O_CREAT)        || die $!;
    sysopen(FH, $path, O_WRONLY|O_TRUNC|O_CREAT, 0666)  || die $!;

To open file for writing, create new file, file must not exist:

    sysopen(FH, $path, O_WRONLY|O_EXCL|O_CREAT)         || die $!;
    sysopen(FH, $path, O_WRONLY|O_EXCL|O_CREAT, 0666)   || die $!;

To open file for appending, create if necessary:

    open(FH, ">> $path") || die $!;
    sysopen(FH, $path, O_WRONLY|O_APPEND|O_CREAT)       || die $!;
    sysopen(FH, $path, O_WRONLY|O_APPEND|O_CREAT, 0666) || die $!;

To open file for appending, file must exist:

    sysopen(FH, $path, O_WRONLY|O_APPEND)               || die $!;

To open file for update, file must exist:

    open(FH, "+< $path")                                || die $!;
    sysopen(FH, $path, O_RDWR)                          || die $!;

To open file for update, create file if necessary:

    sysopen(FH, $path, O_RDWR|O_CREAT)                  || die $!;
    sysopen(FH, $path, O_RDWR|O_CREAT, 0666)            || die $!;

To open file for update, file must not exist:

    sysopen(FH, $path, O_RDWR|O_EXCL|O_CREAT)           || die $!;
    sysopen(FH, $path, O_RDWR|O_EXCL|O_CREAT, 0666)     || die $!;

To open a file without blocking, creating if necessary:

    sysopen(FH, "/tmp/somefile", O_WRONLY|O_NDELAY|O_CREAT)
            or die "can't open /tmp/somefile: $!":

Be warned that neither creation nor deletion of files is guaranteed to
be an atomic operation over NFS.  That is, two processes might both
successfully create or unlink the same file!  Therefore O_EXCL
isn't as exclusive as you might wish.

See also the new L<perlopentut> if you have it (new for 5.6).

=head2 Why do I sometimes get an "Argument list too long" when I use <*>?

The C<< <> >> operator performs a globbing operation (see above).
In Perl versions earlier than v5.6.0, the internal glob() operator forks
csh(1) to do the actual glob expansion, but
csh can't handle more than 127 items and so gives the error message
C<Argument list too long>.  People who installed tcsh as csh won't
have this problem, but their users may be surprised by it.

To get around this, either upgrade to Perl v5.6.0 or later, do the glob
yourself with readdir() and patterns, or use a module like File::KGlob,
one that doesn't use the shell to do globbing.

=head2 Is there a leak/bug in glob()?

Due to the current implementation on some operating systems, when you
use the glob() function or its angle-bracket alias in a scalar
context, you may cause a memory leak and/or unpredictable behavior.  It's
best therefore to use glob() only in list context.

=head2 How can I open a file with a leading ">" or trailing blanks?

Normally perl ignores trailing blanks in filenames, and interprets
certain leading characters (or a trailing "|") to mean something
special. 

The three argument form of open() lets you specify the mode
separately from the filename.  The open() function treats
special mode characters and whitespace in the filename as 
literals

        open FILE, "<", "  file  ";  # filename is "   file   "
        open FILE, ">", ">file";     # filename is ">file"
        

It may be a lot clearer to use sysopen(), though:

    use Fcntl;
    $badpath = "<<<something really wicked   ";
    sysopen (FH, $badpath, O_WRONLY | O_CREAT | O_TRUNC)
        or die "can't open $badpath: $!";

=head2 How can I reliably rename a file?

If your operating system supports a proper mv(1) utility or its functional
equivalent, this works:

    rename($old, $new) or system("mv", $old, $new);

It may be more portable to use the File::Copy module instead.
You just copy to the new file to the new name (checking return
values), then delete the old one.  This isn't really the same
semantically as a rename(), which preserves meta-information like
permissions, timestamps, inode info, etc.

Newer versions of File::Copy export a move() function.

=head2 How can I lock a file?

Perl's builtin flock() function (see L<perlfunc> for details) will call
flock(2) if that exists, fcntl(2) if it doesn't (on perl version 5.004 and
later), and lockf(3) if neither of the two previous system calls exists.
On some systems, it may even use a different form of native locking.
Here are some gotchas with Perl's flock():

=over 4

=item 1

Produces a fatal error if none of the three system calls (or their
close equivalent) exists.

=item 2

lockf(3) does not provide shared locking, and requires that the
filehandle be open for writing (or appending, or read/writing).

=item 3

Some versions of flock() can't lock files over a network (e.g. on NFS file
systems), so you'd need to force the use of fcntl(2) when you build Perl.
But even this is dubious at best.  See the flock entry of L<perlfunc>
and the F<INSTALL> file in the source distribution for information on
building Perl to do this.

Two potentially non-obvious but traditional flock semantics are that
it waits indefinitely until the lock is granted, and that its locks are
I<merely advisory>.  Such discretionary locks are more flexible, but
offer fewer guarantees.  This means that files locked with flock() may
be modified by programs that do not also use flock().  Cars that stop
for red lights get on well with each other, but not with cars that don't
stop for red lights.  See the perlport manpage, your port's specific
documentation, or your system-specific local manpages for details.  It's
best to assume traditional behavior if you're writing portable programs.
(If you're not, you should as always feel perfectly free to write
for your own system's idiosyncrasies (sometimes called "features").
Slavish adherence to portability concerns shouldn't get in the way of
your getting your job done.)

For more information on file locking, see also 
L<perlopentut/"File Locking"> if you have it (new for 5.6).

=back

=head2 Why can't I just open(FH, ">file.lock")?

A common bit of code B<NOT TO USE> is this:

    sleep(3) while -e "file.lock";      # PLEASE DO NOT USE
    open(LCK, "> file.lock");           # THIS BROKEN CODE

This is a classic race condition: you take two steps to do something
which must be done in one.  That's why computer hardware provides an
atomic test-and-set instruction.   In theory, this "ought" to work:

    sysopen(FH, "file.lock", O_WRONLY|O_EXCL|O_CREAT)
                or die "can't open  file.lock: $!":

except that lamentably, file creation (and deletion) is not atomic
over NFS, so this won't work (at least, not every time) over the net.
Various schemes involving link() have been suggested, but
these tend to involve busy-wait, which is also subdesirable.

=head2 I still don't get locking.  I just want to increment the number in the file.  How can I do this?

Didn't anyone ever tell you web-page hit counters were useless?
They don't count number of hits, they're a waste of time, and they serve
only to stroke the writer's vanity.  It's better to pick a random number;
they're more realistic.

Anyway, this is what you can do if you can't help yourself.

    use Fcntl qw(:DEFAULT :flock);
    sysopen(FH, "numfile", O_RDWR|O_CREAT)       or die "can't open numfile: $!";
    flock(FH, LOCK_EX)                           or die "can't flock numfile: $!";
    $num = <FH> || 0;
    seek(FH, 0, 0)                               or die "can't rewind numfile: $!";
    truncate(FH, 0)                              or die "can't truncate numfile: $!";
    (print FH $num+1, "\n")                      or die "can't write numfile: $!";
    close FH                                     or die "can't close numfile: $!";

Here's a much better web-page hit counter:

    $hits = int( (time() - 850_000_000) / rand(1_000) );

If the count doesn't impress your friends, then the code might.  :-)

=head2 All I want to do is append a small amount of text to the end of a file.  Do I still have to use locking?

If you are on a system that correctly implements flock() and you use the
example appending code from "perldoc -f flock" everything will be OK
even if the OS you are on doesn't implement append mode correctly (if
such a system exists.) So if you are happy to restrict yourself to OSs
that implement flock() (and that's not really much of a restriction)
then that is what you should do.

If you know you are only going to use a system that does correctly
implement appending (i.e. not Win32) then you can omit the seek() from
the above code.

If you know you are only writing code to run on an OS and filesystem that
does implement append mode correctly (a local filesystem on a modern
Unix for example), and you keep the file in block-buffered mode and you
write less than one buffer-full of output between each manual flushing
of the buffer then each bufferload is almost guaranteed to be written to
the end of the file in one chunk without getting intermingled with
anyone else's output. You can also use the syswrite() function which is
simply a wrapper around your systems write(2) system call.

There is still a small theoretical chance that a signal will interrupt
the system level write() operation before completion.  There is also a
possibility that some STDIO implementations may call multiple system
level write()s even if the buffer was empty to start.  There may be some
systems where this probability is reduced to zero.

=head2 How do I randomly update a binary file?

If you're just trying to patch a binary, in many cases something as
simple as this works:

    perl -i -pe 's{window manager}{window mangler}g' /usr/bin/emacs

However, if you have fixed sized records, then you might do something more
like this:

    $RECSIZE = 220; # size of record, in bytes
    $recno   = 37;  # which record to update
    open(FH, "+<somewhere") || die "can't update somewhere: $!";
    seek(FH, $recno * $RECSIZE, 0);
    read(FH, $record, $RECSIZE) == $RECSIZE || die "can't read record $recno: $!";
    # munge the record
    seek(FH, -$RECSIZE, 1);
    print FH $record;
    close FH;

Locking and error checking are left as an exercise for the reader.
Don't forget them or you'll be quite sorry.

=head2 How do I get a file's timestamp in perl?

If you want to retrieve the time at which the file was last
read, written, or had its meta-data (owner, etc) changed,
you use the B<-M>, B<-A>, or B<-C> file test operations as
documented in L<perlfunc>.  These retrieve the age of the
file (measured against the start-time of your program) in
days as a floating point number. Some platforms may not have
all of these times.  See L<perlport> for details. To
retrieve the "raw" time in seconds since the epoch, you
would call the stat function, then use localtime(),
gmtime(), or POSIX::strftime() to convert this into
human-readable form.

Here's an example:

    $write_secs = (stat($file))[9];
    printf "file %s updated at %s\n", $file,
        scalar localtime($write_secs);

If you prefer something more legible, use the File::stat module
(part of the standard distribution in version 5.004 and later):

    # error checking left as an exercise for reader.
    use File::stat;
    use Time::localtime;
    $date_string = ctime(stat($file)->mtime);
    print "file $file updated at $date_string\n";

The POSIX::strftime() approach has the benefit of being,
in theory, independent of the current locale.  See L<perllocale>
for details.

=head2 How do I set a file's timestamp in perl?

You use the utime() function documented in L<perlfunc/utime>.
By way of example, here's a little program that copies the
read and write times from its first argument to all the rest
of them.

    if (@ARGV < 2) {
        die "usage: cptimes timestamp_file other_files ...\n";
    }
    $timestamp = shift;
    ($atime, $mtime) = (stat($timestamp))[8,9];
    utime $atime, $mtime, @ARGV;

Error checking is, as usual, left as an exercise for the reader.

Note that utime() currently doesn't work correctly with Win95/NT
ports.  A bug has been reported.  Check it carefully before using
utime() on those platforms.

=head2 How do I print to more than one file at once?

If you only have to do this once, you can do this:

    for $fh (FH1, FH2, FH3) { print $fh "whatever\n" }

To connect up to one filehandle to several output filehandles, it's
easiest to use the tee(1) program if you have it, and let it take care
of the multiplexing:

    open (FH, "| tee file1 file2 file3");

Or even:

    # make STDOUT go to three files, plus original STDOUT
    open (STDOUT, "| tee file1 file2 file3") or die "Teeing off: $!\n";
    print "whatever\n"                       or die "Writing: $!\n";
    close(STDOUT)                            or die "Closing: $!\n";

Otherwise you'll have to write your own multiplexing print
function--or your own tee program--or use Tom Christiansen's,
at http://www.cpan.org/authors/id/TOMC/scripts/tct.gz , which is
written in Perl and offers much greater functionality
than the stock version.

=head2 How can I read in an entire file all at once?

The customary Perl approach for processing all the lines in a file is to
do so one line at a time:

    open (INPUT, $file)         || die "can't open $file: $!";
    while (<INPUT>) {
        chomp;
        # do something with $_
    } 
    close(INPUT)                || die "can't close $file: $!";

This is tremendously more efficient than reading the entire file into
memory as an array of lines and then processing it one element at a time,
which is often--if not almost always--the wrong approach.  Whenever
you see someone do this:

    @lines = <INPUT>;

you should think long and hard about why you need everything loaded
at once.  It's just not a scalable solution.  You might also find it
more fun to use the standard DB_File module's $DB_RECNO bindings,
which allow you to tie an array to a file so that accessing an element
the array actually accesses the corresponding line in the file.

On very rare occasion, you may have an algorithm that demands that
the entire file be in memory at once as one scalar.  The simplest solution
to that is

    $var = `cat $file`;

Being in scalar context, you get the whole thing.  In list context,
you'd get a list of all the lines:

    @lines = `cat $file`;

This tiny but expedient solution is neat, clean, and portable to
all systems on which decent tools have been installed.  For those
who prefer not to use the toolbox, you can of course read the file
manually, although this makes for more complicated code.

    {
        local(*INPUT, $/);
        open (INPUT, $file)     || die "can't open $file: $!";
        $var = <INPUT>;
    }

That temporarily undefs your record separator, and will automatically 
close the file at block exit.  If the file is already open, just use this:

    $var = do { local $/; <INPUT> };

=head2 How can I read in a file by paragraphs?

Use the C<$/> variable (see L<perlvar> for details).  You can either
set it to C<""> to eliminate empty paragraphs (C<"abc\n\n\n\ndef">,
for instance, gets treated as two paragraphs and not three), or
C<"\n\n"> to accept empty paragraphs.

Note that a blank line must have no blanks in it.  Thus 
S<C<"fred\n \nstuff\n\n">> is one paragraph, but C<"fred\n\nstuff\n\n"> is two.

=head2 How can I read a single character from a file?  From the keyboard?

You can use the builtin C<getc()> function for most filehandles, but
it won't (easily) work on a terminal device.  For STDIN, either use
the Term::ReadKey module from CPAN or use the sample code in
L<perlfunc/getc>.

If your system supports the portable operating system programming
interface (POSIX), you can use the following code, which you'll note
turns off echo processing as well.

    #!/usr/bin/perl -w
    use strict;
    $| = 1;
    for (1..4) {
        my $got;
        print "gimme: ";
        $got = getone();
        print "--> $got\n";
    }
    exit;

    BEGIN {
        use POSIX qw(:termios_h);

        my ($term, $oterm, $echo, $noecho, $fd_stdin);

        $fd_stdin = fileno(STDIN);

        $term     = POSIX::Termios->new();
        $term->getattr($fd_stdin);
        $oterm     = $term->getlflag();

        $echo     = ECHO | ECHOK | ICANON;
        $noecho   = $oterm & ~$echo;

        sub cbreak {
            $term->setlflag($noecho);
            $term->setcc(VTIME, 1);
            $term->setattr($fd_stdin, TCSANOW);
        }

        sub cooked {
            $term->setlflag($oterm);
            $term->setcc(VTIME, 0);
            $term->setattr($fd_stdin, TCSANOW);
        }

        sub getone {
            my $key = '';
            cbreak();
            sysread(STDIN, $key, 1);
            cooked();
            return $key;
        }

    }

    END { cooked() }

The Term::ReadKey module from CPAN may be easier to use.  Recent versions
include also support for non-portable systems as well.

    use Term::ReadKey;
    open(TTY, "</dev/tty");
    print "Gimme a char: ";
    ReadMode "raw";
    $key = ReadKey 0, *TTY;
    ReadMode "normal";
    printf "\nYou said %s, char number %03d\n",
        $key, ord $key;

=head2 How can I tell whether there's a character waiting on a filehandle?

The very first thing you should do is look into getting the Term::ReadKey
extension from CPAN.  As we mentioned earlier, it now even has limited
support for non-portable (read: not open systems, closed, proprietary,
not POSIX, not Unix, etc) systems.

You should also check out the Frequently Asked Questions list in
comp.unix.* for things like this: the answer is essentially the same.
It's very system dependent.  Here's one solution that works on BSD
systems:

    sub key_ready {
        my($rin, $nfd);
        vec($rin, fileno(STDIN), 1) = 1;
        return $nfd = select($rin,undef,undef,0);
    }

If you want to find out how many characters are waiting, there's
also the FIONREAD ioctl call to be looked at.  The I<h2ph> tool that
comes with Perl tries to convert C include files to Perl code, which
can be C<require>d.  FIONREAD ends up defined as a function in the
I<sys/ioctl.ph> file:

    require 'sys/ioctl.ph';

    $size = pack("L", 0);
    ioctl(FH, FIONREAD(), $size)    or die "Couldn't call ioctl: $!\n";
    $size = unpack("L", $size);

If I<h2ph> wasn't installed or doesn't work for you, you can
I<grep> the include files by hand:

    % grep FIONREAD /usr/include/*/*
    /usr/include/asm/ioctls.h:#define FIONREAD      0x541B

Or write a small C program using the editor of champions:

    % cat > fionread.c
    #include <sys/ioctl.h>
    main() {
        printf("%#08x\n", FIONREAD);
    }
    ^D
    % cc -o fionread fionread.c
    % ./fionread
    0x4004667f

And then hard code it, leaving porting as an exercise to your successor.

    $FIONREAD = 0x4004667f;         # XXX: opsys dependent

    $size = pack("L", 0);
    ioctl(FH, $FIONREAD, $size)     or die "Couldn't call ioctl: $!\n";
    $size = unpack("L", $size);

FIONREAD requires a filehandle connected to a stream, meaning that sockets,
pipes, and tty devices work, but I<not> files.

=head2 How do I do a C<tail -f> in perl?

First try

    seek(GWFILE, 0, 1);

The statement C<seek(GWFILE, 0, 1)> doesn't change the current position,
but it does clear the end-of-file condition on the handle, so that the
next <GWFILE> makes Perl try again to read something.

If that doesn't work (it relies on features of your stdio implementation),
then you need something more like this:

        for (;;) {
          for ($curpos = tell(GWFILE); <GWFILE>; $curpos = tell(GWFILE)) {
            # search for some stuff and put it into files
          }
          # sleep for a while
          seek(GWFILE, $curpos, 0);  # seek to where we had been
        }

If this still doesn't work, look into the POSIX module.  POSIX defines
the clearerr() method, which can remove the end of file condition on a
filehandle.  The method: read until end of file, clearerr(), read some
more.  Lather, rinse, repeat.

There's also a File::Tail module from CPAN.

=head2 How do I dup() a filehandle in Perl?

If you check L<perlfunc/open>, you'll see that several of the ways
to call open() should do the trick.  For example:

    open(LOG, ">>/tmp/logfile");
    open(STDERR, ">&LOG");

Or even with a literal numeric descriptor:

   $fd = $ENV{MHCONTEXTFD};
   open(MHCONTEXT, "<&=$fd");   # like fdopen(3S)

Note that "<&STDIN" makes a copy, but "<&=STDIN" make
an alias.  That means if you close an aliased handle, all
aliases become inaccessible.  This is not true with 
a copied one.

Error checking, as always, has been left as an exercise for the reader.

=head2 How do I close a file descriptor by number?

This should rarely be necessary, as the Perl close() function is to be
used for things that Perl opened itself, even if it was a dup of a
numeric descriptor as with MHCONTEXT above.  But if you really have
to, you may be able to do this:

    require 'sys/syscall.ph';
    $rc = syscall(&SYS_close, $fd + 0);  # must force numeric
    die "can't sysclose $fd: $!" unless $rc == -1;

Or, just use the fdopen(3S) feature of open():

    { 
        local *F; 
        open F, "<&=$fd" or die "Cannot reopen fd=$fd: $!";
        close F;
    }

=head2 Why can't I use "C:\temp\foo" in DOS paths?  Why doesn't `C:\temp\foo.exe` work?

Whoops!  You just put a tab and a formfeed into that filename!
Remember that within double quoted strings ("like\this"), the
backslash is an escape character.  The full list of these is in
L<perlop/Quote and Quote-like Operators>.  Unsurprisingly, you don't
have a file called "c:(tab)emp(formfeed)oo" or
"c:(tab)emp(formfeed)oo.exe" on your legacy DOS filesystem.

Either single-quote your strings, or (preferably) use forward slashes.
Since all DOS and Windows versions since something like MS-DOS 2.0 or so
have treated C</> and C<\> the same in a path, you might as well use the
one that doesn't clash with Perl--or the POSIX shell, ANSI C and C++,
awk, Tcl, Java, or Python, just to mention a few.  POSIX paths
are more portable, too.

=head2 Why doesn't glob("*.*") get all the files?

Because even on non-Unix ports, Perl's glob function follows standard
Unix globbing semantics.  You'll need C<glob("*")> to get all (non-hidden)
files.  This makes glob() portable even to legacy systems.  Your
port may include proprietary globbing functions as well.  Check its
documentation for details.

=head2 Why does Perl let me delete read-only files?  Why does C<-i> clobber protected files?  Isn't this a bug in Perl?

This is elaborately and painstakingly described in the
F<file-dir-perms> article in the "Far More Than You Ever Wanted To
Know" collection in http://www.cpan.org/olddoc/FMTEYEWTK.tgz .

The executive summary: learn how your filesystem works.  The
permissions on a file say what can happen to the data in that file.
The permissions on a directory say what can happen to the list of
files in that directory.  If you delete a file, you're removing its
name from the directory (so the operation depends on the permissions
of the directory, not of the file).  If you try to write to the file,
the permissions of the file govern whether you're allowed to.

=head2 How do I select a random line from a file?

Here's an algorithm from the Camel Book:

    srand;
    rand($.) < 1 && ($line = $_) while <>;

This has a significant advantage in space over reading the whole
file in.  A simple proof by induction is available upon 
request if you doubt the algorithm's correctness.

=head2 Why do I get weird spaces when I print an array of lines?

Saying

    print "@lines\n";

joins together the elements of C<@lines> with a space between them.
If C<@lines> were C<("little", "fluffy", "clouds")> then the above
statement would print

    little fluffy clouds

but if each element of C<@lines> was a line of text, ending a newline
character C<("little\n", "fluffy\n", "clouds\n")> then it would print:

    little
     fluffy
     clouds

If your array contains lines, just print them:

    print @lines;

=head1 AUTHOR AND COPYRIGHT

Copyright (c) 1997-2002 Tom Christiansen and Nathan Torkington.
All rights reserved.

This documentation is free; you can redistribute it and/or modify it
under the same terms as Perl itself.

Irrespective of its distribution, all code examples here are in the public
domain.  You are permitted and encouraged to use this code and any
derivatives thereof in your own programs for fun or for profit as you
see fit.  A simple comment in the code giving credit to the FAQ would
be courteous but is not required.